ماژول رگولاتور افزاینده lm2577 lm2596 با خروجی 1.25V-25V/3A

DC-DC Step Up Down Boost buck Voltage Converter Module LM2577S LM2596S Power

(دیدگاه {{model.count}} کاربر)
تعداد
نوع
آماده ارسال ناموجود
  • {{value}}
کمی صبر کنید...

این ماژول ار رگولاتورهای lm2577 و lm2596 استفاده می کند و ورودی آن 4V-35V و خروجی آن 2.5V-25V با جریان 3A قابل تنظیم می باشد.

Specification:

- Input Voltage :4-35V
- Output voltage: Continuously adjustable(1.25-25V unload adjust)
- Output current: 3A Max(If more than 15W, please install the heat sink)
- CC range :0-2A (adjustable)
- Revolving light current: CC value * (1%-100%), default is 0.1 times
- Minimum voltage difference: 2V
- Output power: natural cooling 15W
- Conversion efficiency: 80% (the higher the output voltage, the higher the efficiency)
- Operating Temperature: Industrial (-40 ℃ to +85 ℃) (ambient temperature more than 40℃, lower power use, or add heat sink)\
- Full load temperature rise: 45 ℃
- Indicator: CC indicator is Red, charging indicator is Red, charging completed the indicator is Blue.
- Output short circuit protection: Yes, constant current.
- Connect method: Can solder on the PCB with wire directly
- Input: IN+ input Positive is, IN- input negative
- Output: OUT+ output is positive, OUT- output negative
- Module Size: 50 x 37 x 13mm

This module power output is affect by the module itself-capacity and pre-and post-class load and other factors; the following data for professional equipment measured results, without considering other factors.
Power supply module is a kind of electronic components, please don't buy the item if you have no electronic expertise.
This Module Properties: It is non-isolated step-down constant current, constant voltage module (CC CV) charging module

Some Applications:

- High-power LED constant current driver.
- Lithium batteries (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charge.
- Solar panels, wind generator voltage regulator circuit board power supply, such as automatic buck regulator circuit.

Battery use:

- Make sure of the voltage and current of the battery you need to charge
- Adjust the constant voltage potentiometer to make sure the output Voltage is about 5V(about).
- Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected charging current value
- The charge current of transfer lamp is default 0.1 times of the charging current (constant current value)
- Adjust the constant voltage potentiometer to make sure the output Voltage is up to floating Voltage.
Connected to the battery and try to charging (for previous 5 steps, module input terminal is connected to power source, output load is NOT connected to batteries).

LED Constant Current Driver Use:

- Make sure operating current and Max operating Voltage of the LED you need to drive.
- Adjust the constant voltage potentiometer to make sure the output Voltage is 5V(about).
- Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer. To make sure the output current to the expected LED operating current.
- Adjust the constant voltage potentiometer to make sure the output Voltage is up to LED Max operating Voltage.
- Join LED, test (For the above 3 steps, module input terminal is connected to power source, output load is NOT connected to LED).


دیدگاه خود را بنویسید

  • {{value}}
این دیدگاه به عنوان پاسخ شما به دیدگاهی دیگر ارسال خواهد شد. برای صرف نظر از ارسال این پاسخ، بر روی گزینه‌ی انصراف کلیک کنید.
دیدگاه خود را بنویسید.
کمی صبر کنید...